Nashville DTV News

WNPX-LD 24 is Now Broadcasting

- Posted February 1st, 2022 at 9:17pm
I just found out that WNPX-LD channel 24 has just started broadcasting. Just to be clear, this station no longer has any connection to the ION station WNPX 28 (RF 32). I am too far away to see what is on the channel. So I am asking any one that lives near their broadcasting antenna, which is located in Williamson County along Clovercroft Road, what are they broadcasting? Since they are owned by the Daystar religious group, I am going to suspect they are showing the Daystar network, but that is just my guess. Thank you for any one who can tell me what their programming is. Until more news breaks, that's all for now.

Update 2/2/22 at 1:43pm: - I just got confirmation that they are broadcasting a total of three channels. They are as follows:

20.1 WNPX-LD (Daystar) (I'm guessing)
20.2 LATINO (?)
20.3 BRAZIL (?)

The reason for the question marks is because I know the names of each channel, but I don't know what the content is being shown. If anybody can shed a light on what the content is, then let me know down below in the comments. Until more news breaks, that's all for now.


- Posted on February 2nd, 2022 at 6:08am

I'm in the Tusculum area near Antioch. I pointed my antenna south west and I am getting nothing. Are you sure they are on the air? They have a lousy signal if they are on the air. I should be able to receive a signal.

- Posted on February 2nd, 2022 at 1:38pm

Yes, they are broadcasting, and I just got confirmation on what channels they are showing. I don't know the content, but I know they have three channels altogether - 20.1 WNPX-LD (Daystar), 20.2 LATINO (?), and 20.3 BRAZIL (?). Here is where I am getting my information - This is a person that lives in Franklin. They are broadcasting at 12kw, but from what I know about the tower, it is a short tower. That maybe the reason for not many people receiving the channel. Here is the broadcasting range -

- Posted on February 2nd, 2022 at 1:46pm

It must be a real short antenna because I get channel 15 well and their antenna is below 500 feet.

- Posted on February 2nd, 2022 at 1:49pm

You are correct sir. I just compared the heights of both towers and 15 is at 459' while 20 (rf 24) is at just 276'.

- Posted on February 2nd, 2022 at 1:56pm

That's the problem, no doubt.

- Posted on February 2nd, 2022 at 11:33am

I live in Dickson. Did a scan; but no signal. Just a black screen.

Brentwood OTA
- Posted on February 3rd, 2022 at 7:59am

I'm right here in Brentwood, less than 10 miles from that antenna, and I can't pick it up on my upstairs TV. Maybe I'll hsve better luck on a clear day.

- Posted on February 4th, 2022 at 3:11pm

Signal map.

- Posted on February 8th, 2022 at 4:23pm

I live in Donelson and I can not get WNPX-LD .

- Posted on February 8th, 2022 at 8:40pm

A lot of people can't pick them up. I guess on a count of them being on a not-so-tall tower because they are only 276 ft off the ground on top of a hill. Here is a link to their broadcasting range -

- Posted on February 13th, 2022 at 3:29pm - Edited

I live off Wilson Pike and can see the broadcast tower from my house. I cannot pick up a signal unless I point my antenna directly toward the tower (plus or minus 10 degrees) . I pick up 20.1, 20.2, and 20.3.

- Posted on January 21st, 2023 at 1:25pm

I’ve been unable to get this station lately, despite my tuner showing enough signal strength that I should. I can’t recall how long it’s been since I was able to get it. Is anyone else able to watch this station? I think they may have a technical issue going on with their signal

- Posted on January 21st, 2023 at 3:20pm

I just checked someone's tuner reception near Franklin, and yes, they are still broadcasting.

- Posted on January 21st, 2023 at 4:35pm

WNPX-LD is still broadcasting, but there is nothing on it. It comes in as channel 24 with no virtual channels (no 20.1, 20.2 or 20.3) and the picture is blank. It's been this way for the last two or three weeks.

The "Add a Comment" Section - (You need to be signed in to comment.)

    *To add a brand new comment, please refresh the page.